烧结温度对莫来石多孔陶瓷结构与性能的影响

doi:10.3969/j.issn.1001-1935.2023.01.003

耐火材料 ›› 2023, Vol. 57 ›› Issue (1): 10-14.DOI: 10.3969/j.issn.1001-1935.2023.01.003

烧结温度对莫来石多孔陶瓷结构与性能的影响

郭会师¹⁾, 陈文亮¹⁾, 李文凤²⁾, 杨佳麟¹⁾, 秦笑梅¹⁾, 桂阳海¹⁾, 刘应凡¹⁾

1)郑州轻工业大学材料与化学工程学院河南郑州 450001
2)河南工业大学材料科学与工程学院河南郑州 450001

收稿日期:2022-05-19 出版日期:2023-02-15 发布日期:2023-02-21
作者简介:郭会师:男,1984年生,博士,讲师。E-mail:guohuishi@zzuli.edu.cn
基金资助:
国家自然科学基金资助项目(51802290,U1904213,U20041102);河南省重点科技攻关项目(182102210613,202102210260,172102210223)。

Effects of sintering temperatures on microstructure and properties of mullite porous ceramics

Guo Huishi, Chen Wenliang, Li Wenfeng, Yang Jialin, Qin Xiaomei, Gui Yanghai, Liu Yingfan

School of Material and Chemical Engineering,Zhengzhou University of Light Industry,Zhengzhou 450001,Henan,China

Received:2022-05-19 Online:2023-02-15 Published:2023-02-21

摘要/Abstract

摘要： 以含锆硅线石为主要原料,α-Al₂O₃粉为辅料,改性淀粉为造孔剂,原位烧结制备了莫来石多孔陶瓷试样。研究了烧结温度(1 400~1 600 ℃,间隔50 ℃)对试样物相组成、显微结构及性能的影响。结果表明:1)随烧结温度的升高,试样中莫来石衍射峰的强度逐渐增强,莫来石晶粒逐渐发育长大,其外观呈现明显的台阶状形貌,符合二维成核生长机制。2)随烧结温度的升高,烧后试样的体积密度呈先减后增趋势,而显气孔率和线变化率的变化趋势则与之相反,常温耐压强度则呈逐渐增大趋势。3)当烧结温度为1 550~1 600 ℃时,试样综合性能较佳,莫来石晶粒发育长大并致密结合,适于在高温下使用。

关键词: 硅线石, 莫来石, 多孔陶瓷, 烧结温度, 生长机制

Abstract: Mullite porous ceramics were prepared by in-situ sintering using zirconia-containing sillimanite as the main raw material,α-Al₂O₃ powder as the auxiliary material and modified starch as the pore-forming agent.The effects of the sintering temperature (1 400-1 600 ℃,an interval of 50 ℃) on the phase composition,the microstructure and the properties of the samples were studied.The results show that:(1)with the increase of the sintering temperature,the intensity of the mullite diffraction peaks increases and the mullite crystals gradually grow up;moreover,steps are observed on mullite surfaces,indicating that the mullite grows by two-dimensional nucleation mechanism;(2)with the increase of the sintering temperature,the bulk density of the samples decreases firstly and then increases,while the apparent porosity and the linear change show the opposite trends,but the cold compressive strength increases gradually;(3)when the sintering temperature is 1 550-1 600 ℃,the samples show the optimal comprehensive properties;mullite crystals grow up and combine closely,which makes mullite porous ceramics suitable for application at high temperatures.

Key words: sillimanite, mullite, porous ceramic, sintering temperature, growth mechanism

中图分类号:

TQ175

郭会师, 陈文亮, 李文凤, 杨佳麟, 秦笑梅, 桂阳海, 刘应凡. 烧结温度对莫来石多孔陶瓷结构与性能的影响[J]. 耐火材料, 2023, 57(1): 10-14.

Guo Huishi, Chen Wenliang, Li Wenfeng, Yang Jialin, Qin Xiaomei, Gui Yanghai, Liu Yingfan. Effects of sintering temperatures on microstructure and properties of mullite porous ceramics[J]. Refractories, 2023, 57(1): 10-14.

参考文献

[1] 冯鑫,李文凤,郭会师,等.隔热用多孔陶瓷材料制备方法的研究进展 [J].陶瓷学报,2022,43(2):186-195.
[2] 王露露,马北越,刘春明,等.多孔莫来石性能优化的研究进展 [J].耐火材料,2021,55 (6):549-552.
[3] 何江锋,张海军,葛胜涛,等.SiC多孔陶瓷制备方法研究进展 [J].耐火材料,2020,54 (2):163-171.
[4] GUO H S,LI W F,YE F B,et al.Preparation of microporous mullite ceramics by foaming for high temperature thermal isolation[J].Ceramics International,2016,42(15):17332-17338.
[5] LIU Y,XU L,CHEN M,et al.Effects of andalusite and kyanite addition on the microstructure,thermo-mechanical properties and corrosion resistance of ultralow-cement bauxite-corundum castables[J].Ceramics International,2022,48(10):14141-14150.
[6] ZHOU W Y,YAN W,LI N,et al.Fabrication and characterization of a mullite-foamed ceramic reinforced by in-situ SiC whiskers[J].Ceramics International,2020,46(3):3132-3138.
[7] SCHNEIDER H,SCHREUER J,HILDMANN B.Structure and properties of mullite—A review[J].Journal of the European Ceramic Society,2008,28(2):329-344.
[8] 王刚,袁波,韩建燊,等.发泡法制备氧化铝基多孔陶瓷(Ⅱ):氧化铝复相多孔陶瓷的制备、组成、结构和性能[J].耐火材料,2017,51(5):329-333+343.
[9] GUO H S,YE F B,LI W F,et al.Preparation and characterization of foamed microporous mullite ceramics based on kyanite[J].Ceramics International,2015,41(10):14645-14651.
[10] GUO H S,LI W F.Effects of Al₂O₃ crystal types on morphologies,formation mechanisms of mullite and properties of porous mullite ceramics based on kyanite [J].Journal of the European Ceramic Society,2018,38(2):679-686.
[11] DENG X G,RAN S L,HAN L,et al.Foam-gelcasting preparation of high-strength self-reinforced porous mullite ceramics[J].Journal of the European Ceramic Society,2017,37(13):4059-4066.
[12] 郭会师,杨政宏,李文凤,等.蓝晶石基微孔莫来石陶瓷分离膜支撑体的制备、结构与性能研究 [J].硅酸盐通报,2015,34(12):3546-3550+3556.
[13] 熊洵,刘浩,马妍,等.多孔莫来石陶瓷制备与性能研究 [J].耐火材料,2019,53(5):336-341+347.
[14] 高光斌,鄢文,李楠,等.硅线石含量对轻质莫来石-刚玉耐火材料的显微结构与性能的影响 [J].硅酸盐通报,2017,36(4):1395-1400+1405.
[15] GUO H S,LI W F,YE F B.Low-cost porous mullite ceramic membrane supports fabricated from kyanite by casting and reaction sintering[J].Ceramics International,2016,42(4):4819-4826.
[16] 林彬荫,刘惠珍.硅线石基本性能与莫来石化行为[J].耐火材料,1989,23(1):20-24.
[17] 林彬荫.蓝晶石红柱石硅线石[M].北京:冶金工业出版社,1998:100-102.

烧结温度对莫来石多孔陶瓷结构与性能的影响

Effects of sintering temperatures on microstructure and properties of mullite porous ceramics

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	昝文宇, 马北越, 陈广鑫, 曹长坤, 李孟强. 利用低压电瓷废料和二次铝灰制备莫来石陶瓷基多孔骨料[J]. 耐火材料, 2024, 58(4): 302-306.
[2]	高云琴, 郭凯歌, 马爱琼, 牛兴荣, 杨光, 张旭东. 莫来石-刚玉-镁铝尖晶石复相材料的抗碱侵蚀性能研究[J]. 耐火材料, 2024, 58(4): 334-340.
[3]	李坤鹏, 闫双志, 张涛, 石鹏坤, 冯志源, 范沐旭, 王晗, 刘鹏程. 回转窑炉渣对刚玉-莫来石砖的侵蚀研究[J]. 耐火材料, 2024, 58(4): 349-353.
[4]	邵荣丹, 鞠茂奇, 程水明, 夏昌勇, 李旭治, 张寒, 单江博. 氧化硼对Al₂O₃-SiC-C质浇注料力学性能的影响[J]. 耐火材料, 2024, 58(3): 230-233.
[5]	张会, 柴倩, 张红, 王艺兴, 郝晨曦, 王星雨. 氧化锆和氧化镧共掺杂对堇青石多孔陶瓷性能的影响[J]. 耐火材料, 2024, 58(2): 99-103.
[6]	杨德凯, 王周福, 刘浩, 马妍, 王玺堂, 周晶. 土壤聚合物的制备及其对刚玉质浇注料性能的影响[J]. 耐火材料, 2024, 58(2): 104-109.
[7]	刘静静, 岳卫东, 熊飞, 单言芳. 网状孔壁碳化硅基多孔陶瓷的制备及其颗粒物过滤研究[J]. 耐火材料, 2024, 58(2): 132-136.
[8]	孙华云. 低品位蓝晶石制备锂离子电池窑炉用莫来石轻质隔热材料[J]. 耐火材料, 2024, 58(2): 155-160.
[9]	孙家朐, 刘新, 吴锋, 何慧龄, 罗旭东. 工业固废制备莫来石材料的研究进展[J]. 耐火材料, 2024, 58(2): 174-178.
[10]	秦梦黎, 罗颖, 申自强, 刘梦, 宋杰光, 王慈, 刘强. 莫来石晶须/陶瓷纤维增强堇青石质隔热材料[J]. 耐火材料, 2024, 58(1): 8-12.
[11]	朴佳思, 杜庆洋, 唐钰栋, 白佳海. 轻烧MgO粉对凝胶注模法制备MgAl₂O₄多孔陶瓷性能的影响[J]. 耐火材料, 2024, 58(1): 40-43.
[12]	夏玉婷, 杨文博, 饶羽彤, 聂锐杉, 姚远. 轻质高强莫来石浇注料的组分优化和性能增强[J]. 耐火材料, 2024, 58(1): 72-75.
[13]	苏玉柱, 罗华明, 王涵宇, 范明明, 金懿, 占华生. 矾土基莫来石的性能分析[J]. 耐火材料, 2024, 58(1): 76-79.
[14]	张巍, 王京阳. 莫来石复合耐火材料的应用进展[J]. 耐火材料, 2024, 58(1): 80-86.
[15]	李鑫, 曹岳岐, 张强, 郭安然. 光固化3D打印制备莫来石纤维基多孔陶瓷[J]. 耐火材料, 2023, 57(6): 461-466.